Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
Are you currently hunting for resources concerning Tools You Need to Install a New Bathtub ?
Installing a tub isn't exactly brain surgery, but it does call for solid plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately tough project. If the old tub is readily available, the project can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub and also place the brand-new tub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub and also set in the brand-new one. See to it you have actually qualified yourself for the work and are comfortable trying it. Rather than employing a contractor to take over a halfway-completed job, it is far better to think about using one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This article will assist you mount a new tub in your bathroom if you have actually currently bought a new tub as well as do not need to change the plan of your previous water pipelines.
Your devices and product checklist ought to make up the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing faucets can be rather troublesome as a result of the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. When the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap as well as the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the tub until the level reviews level.
To mount taps, fit the bottom of the furthest versatile tap adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water system and examine all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub as well as likewise check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bathtub has actually been utilized at the very least when as this will certainly resolve it right into its final placement.
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to avoid pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, causing the water to pass through the wall between the bath and the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the tub with water prior to securing, to enable the activity experienced when the bathtub is in usage. The sealer can break rather very early if you do not take into consideration this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the marketplace. It is suggested to fit the ceramic tiles using waterproof or water-proof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub? Write feedback down the page. We would be interested to hear your views about this entry. We are looking forward that you come back again later on. Loved our content? Please share it. Help someone else discover it. Thanks for taking the time to read it.
Quote Report this page